Fabulous Frames

By Annette Smyth

Hello there,

Did you catch Tracey Evans on Hochanda on 27th September? if not click here to go to the Hochanda site and watch the shows on rewind at 11am and 3pm. If you did then you will have seen the amazing frames and panels now available from Powertex UK.

The frames are constructed from MDF and provide a beautifully stable base to apply all the lovely Powertex textures onto.

They come in 2 options.

I fell in love with these beauties when I saw them and have been creating like crazy with them. Here are a few of my makes.

Fabulous frames

Mixed Media

I created these pieces using the MDF frame and panel, they are coated in a base of Ivory Powertex and Easy Structure. Texture was added with stencils, mark making, MDF lettering, Powercotton, Paperdecoration and 3D Sand and Balls.

Secret Art Loft acrylic inks were then sprayed on to give the base colours and enhanced with the Secret Art Loft acrylic paints as the colours match perfectly. A little bit of bling was added with gems and silver leaf.

Africa themed mdf frame by Annette Smyth

It’s all about Africa

This piece was also created on the MDF Frame and Panel. This time I used Ivory Powertex along with Easy 3D Flex and 3D Sand to create the base texture.

The mdf additions – trees and letters, were all coated with Powertex Bronze and then stencilled on using Easy Structure to give texture.

The plaster torso (African Semi Prince) was also coated in Powertex Bronze.

A rice paper image was added to the central area using Easy Coat Mat before the lettering was added on top

The whole piece was then drybrushed with Powercolour pigments using Easy Varnish and the same pigments mixed with Powerwax were used to give the depth of colour on the frame area.

Cow skull Powertex art by Annette Smyth

Cow Skull Dreaming

For this piece I used the same frame but combined it with the Dreamcatcher MDF set which I stencilled onto using Easy structure. I used StoneArt clay in the new Cow Skull mould to create the focal point and added lots of extra flowers.

The base was Ivory Powertex and the additional texture is from cardboard, Powercotton, dishcloth, Paperdecoration and 3D Sand and Balls.

Again I used the Secret Art Loft acrylic inks and paints for colouring.

Powertex art by Annette Smyth

Heading East

For the Eastern themed pieces I chose to use the MDF Inset Frame and Panel. The plaster Buddha sits beautifully inside the opening with lots of room around the edges to add texture and colour and the lovely MDF symbols.

The top panel uses Black Powertex, Easy Structure, Hessian and 3D Sand and Balls. Once dry I used Easy Varnish and Rich Gold pigment to add the highlights.

The lower piece used Ivory Powertex, stencilling and texture with Easy Structure. The acrylic inks and paints provide the intense colour and Easy Varnish with Rich Gold pigment was used for the highlights.

Keep an eye out on this Powertex Magazine for some fantastic step by step articles from my design team colleagues. They will show you other amazing projects you can create using these frames.

We love to see what you create so please post your makes on our Facebook group, The Powertex Studio. Inspire others to have a go.

See more of my work or join me for a workshop at my home studio in Leamington Spa. Please take a look at my website www.annettesmyth.co.uk or contact me via my Facebook page.

Until next time Happy Creative Adventures.

Axx

Powertex sculptures from recycled items

Designer – Annette Smyth

One of the great things I love about working with the Powertex product range is the ability to recycle and upcycle everyday objects into something completely different.

I love to create 3D sculptures, especially animals and birds. I often walk around car boots and local charity shops dreaming of all the things I could create from the weird and wonderful items on offer.

Sometimes I find an object that just attracts me but I don’t have an immediate project in mind. In cases like this, I sit the item in my studio and wait until I get that lightbulb moment.

Powertex sculptures from recycled items

Here are a few of my upcycled sculpts.

Lamp bases make great legs!

Lamp base

These beautiful lamps were no longer working and were gifted to me by my good friend Jacqui Mexson. Jacqui knows me so well that she knew I would be over the moon and brimming with ideas with their beautiful shape.

I removed all the electrical gubbins and the lampshades (I’ve reserved these for another project!!). Along with some polystyrene, pipe lagging, foil and masking tape, they were then ready for their transformation into…

Powertex flamigoes by Annette Smyth.  from recycled items.

The flamingoes

Using Powertex Universal Medium, Stone Art and packaging from an Amazon delivery, these birds just came into being.

Candle holders are perfect armatures

Candle holder as a sculpture base

This candle holder was a pleasant find at the local tip shop for the grand price of £1. Candle holders are often solid forms with a decent weight so lend themselves perfectly as armatures. The flowing curves of this treble clef shape immediately called out for a sea themed project. I removed the top flat plate and built up the shape with tin foil to create…

Sea horse by Annette Smyth

A fabric draped seahorse

Again I used Powertex Universal Medium along with pigments and 3D sand and balls for the base.

Empty tape rolls make perfect circles

Powertex fish sculpture by Annette Smyth. from recycled items.

Here I have used the empty masking tape roll to create a perfect circle to build on.

Powertex fish by Annette Smyth

Some foil, masking tape, Easy3D flex and pigments made this fish a fun project.

Plastic milk containers as animal bodies

Powertex rabbit from milk container

My rabbits and dogs are created from 4pt plastic milk containers for the bodies. The cardboard tubes from the centre of rolls of tinfoil are the perfect for shape for legs. Foil enables me to add bulk and shape for the head, ears and paws.

Powertex dog from container Annette Smyth from recycled items

Once formed these are covered in masking tape and painted with a layer of Powertex Universal Medium.

Powertex rabbit from milk container by Annette Smyth

Before being covered with fabric or Stone Art clay.

I hope you have enjoyed seeing a few of my Powertex sculptures from recycled items and that I have inspired you to have a go yourself. If you would like an easy start into sculpting check out my previous article on sculpting penguins.

Don’t forget we would love to see your makes by posting them on the Powertex Studio Facebook group or into the Powertex Addicts Facebook page.

If you would like to join me for a workshop at my home studio then please take a look at the workshops page on my website.

Until next time, Happy Creative Adventures…..Axx

Star dreaming inspiration

By Annette Smyth

Hello everyone. I wonder, is there such a thing as star dreaming?

I hope you are having lots of adventures in this lovely weather we are currently experiencing. One of the things I love at this time of year is being able to sit out in the warm evenings under clear skies and let my mind wander.

Star dreaming

When we look upwards with the naked eye, we can only see spots of light on a dark background. But what is really out there? Thanks to a very talented member of our family, I was able to get access to some amazing shots using astrophotography. This allowed me to get a more detailed view.

Barry Porteous has kindly allowed me to share some of his amazing work with you here. I think these images are just perfect inspiration for Powertex canvas projects. See the images below with my suggestions for the products you could use to recreate them as wall art.

Inspiration

Lunar eclipse

Lunar eclipse Powertex inspiration
Lunar eclipse by Barry Porteous

For this Powertex project – A canvas covered in Black Powertex Universal Medium with a White Powertex circle. Add Stone Art in a circle to give texture. Use Mahogany bister, Easy Varnish and white and red Powercolor to create the deep red colours.

3 day old moon

3 day old moon Powertex inspiration
3 day old moon by Barry Porteous

This Powertex project use Black Powertex Univeral Medium for the background and Ivory for the moon. Mix 3D Sand into a paste for texture. Yellow bister, White and Yellow Ochre Powercolor can be used to create these yellow colours. Mix your pigments with Easy Varnish to make a paint.

Constellation of Cygnus – The Crescent Nebula (5000 light years away)

Star dreaming inspiration
Constellation of Cygnus – the crescent nebula by Barry Porteous

Horsehead and flame nebula and the Leo triplet of galaxies

Star dreaming inspiration

Horsehead and flame nebula by Barry Porteous

Constellation of Cygnus – North American Nebula

Powertex canvas inspiration
Constellation of Cygnus – North American Nebula by Barry Porteous

Recreating Nebula images with Powertex

These Nebula images could all be recreated with Black Powertex Universal Medium for the background. Use Easy Varnish, White and Red Powercolor (dry brushed, splattered and painted for different effects.

I hope you have enjoyed these images and that you are inspired to create your own starscapes. Why not share your creations on the Powertex Studio Facebook group.

If you would like to see more inspiration ideas why not have a look at my previous article or join me for a workshop at my home studio.

Until next time, Happy Creative Adventures………Axx

Powertex Inspiration

Tree bark

Where do you find Powertex inspiration?

by Annette Smyth

Do you find that sometimes your head can be so full of ideas that you have trouble choosing which one to start first. Then there are those times when you just cannot get going no matter what and it is easy to sit in that void. Just think how much more fun it would be to have creative adventures again. Let me show you how to find some Powertex inspiration.

So how do you find inspiration ??

I always find that getting out into nature kick starts my creative flow.

Walking across the local fields not only makes me feel better physically but it also clears my head of all the “shoulds” that are going on in there.  You know the ones……I should be doing the housework, I should tackle that pile of ironing. It also makes space for ideas to take shape again.

Taking photographs of interesting textures often makes me think of new projects. I work out if I could utilise fabric or clay to recreate the texture.

Here are a few of my recent photographs and the ideas that initially came from them

cormorant

1. Terry the Cormorant. He has recently taken up residence in the tree at the bottom of the garden. He’s just a sculpture waiting to happen

Buds and blossoms - powertex inspiration

2. Buds and blossoms. The colours in nature encourage me to step away from my trusted favourites and try new colour ways.

Tree bark - powertex inspiration

3.Tree bark. Crying out to be recreated in Stone Art clay and Easy3D Flex. See my previous blog on mixing stone art clay.

Landscapes

4.Landscapes. These help me to get balance in canvas work. I study what about the image makes it pleasing to me.

Trees - powertex inspiration

5. Trees. These make me want to trail Powertex on a canvas to recreate the tree. I would then build up a mixed media piece on top 

Inspiration from children

6 Izzy – OK, I didn’t find her in the fields but she does inspire me. Her enthusiasm is infectious and the way she works without any thought for right or wrong makes me look at things differently

These photos will sit in my inspiration folder until the time is right for them to be used in a creation.

So how do you find inspiration?  

Why not comment on this blog or leave a photo of one of your inspired makes on the Powertex Studio facebook page.

Until next time, happy creative adventures and don’t forget you can find me and my workshops at www.annettesmyth.co.uk

Axx

I love Powertex!

i love powertex

Powertex, passionately in love ~ Jinny Holt~

What can I say, February is the month for love. I don’t do Valentines but I do love to create and I absolutely LOVE creating with Powertex! I’d even go so far to say I’m kinda obsessed with creating, especially with Powertex involved. It is also fair to say I find being creative a form of therapy. So for this blog, I am going to show you some of my favourite creations and give you a brief description of how I achieved them because I LOVE creating.

I have always been creative from a child and this has never left me, I am lucky enough to create in my full-time job as a Support worker as I am also  their creative coordinator, which means sometimes I get to create and try and pass on my passion of creating to the young adults I work with.

a4 art doll kit powertex
A4 Art Doll Kit

The above creation was made using the newest kit from POWERTEX UK and I loved doing this. I did not stick to my usual pallet which is normally quite dark, so this is a refreshing change for me.

How I created my Art Doll

I used some Easy 3D Flex to create a background with lace and some netting, I dripped Powertex Acrylic paints and pigments down the back panel and used some bister to spray. Then assembled the piece together and added the extra bits to the frame. Next I applied some Stone art to the wings, to give them depth and coloured with the Gold pigment. Then I used some easy 3D to create a paste to go over the wording stencil on the heart. Dry brushed the whole piece with tonal colours and gold. You may have seen this piece on Hochanda.

Powertex frying pan with flower detail

I really could talk about how much I love to Powertex all day, every day!!

This piece above was an old rusty frying pan that I was going to throw out until I had that “light bulb” moment and thought “Ooh I can Powerex it” so I did. I used some of the STOCKINETTE  and an old t-shirt and some crochet material with Bronze Powertex, added some embellishments as a focal point and dry brushed with gold, greens and blues. This piece now resides at my Daughters home as she fell in Love with it.

So another reason for me to LOVE Powertex, you can Powertex anything really, so recycling and upcycling all the way.

See you can use anything, pegs in this piece, to adorn a cheap birdhouse, I hope the photos are self-explanatory!

I think I shall leave this article here for now. I really Love working with Powertex! Did you catch my last article find it here. See you next time Jinny.

You can find all the necessary things at POWERTEXUK

You can find tons of inspiration at THE POWERTEX STUDIO

You can find me on MUMS SHED

Stone Art Clay Powertex Birds

Mixed media Blue Powertex bird Stone Art clay sculptures

Stone Art Clay Birds of Powertex Paradise by Shell North

In December my first Design team blog goodie box arrived! I was so excited!!! I was given the theme of a pair of birds and these are some of the items I received to create something with stone art clay to hopefully inspire others. (eggs, molds and dies are my own)

I did some research for birds in the style of these new MDF bases. I’m usually quite inspired by nature but nothing I found tickled my imagination. So decided to create something whimsical and a little different. Something from my imagination that may represent a bird of paradise. Because sometimes we need thoughts of warmer places of tropical paradise in these colder month in the UK….

thumbnail_20190121_221319

Powertex uk’s favourite product of the month is Stone Art, I decided I was going to use stone art as a clay to cover this piece. I also pulled out my bottle of Blue Powertex liquid art medium. Although I love this colour, I just don’t use it enough! Mixing equal parts of Blue Powertex to stone art powder until I couldn’t stir it anymore. I kneaded it like dough until the stone art granules could not be seen. This was wrapped in cling film and left for a few hours while I prepped everything else.

thumbnail_20190120_191901

First step was to create the bird shape was cut two polystyrene eggs in half long ways and attach them to the breast areas of the MDF bases with masking tape. Molding the 3D shape of the birds with foil and covering in masking tape. Keeping the holes in the MDF bases open for the wire wings by piercing through the eggs with wooden skewers.  Then threading some wire through the bottom holes, I created a wing shape. Inserting the ends of the wires back in through the top holes on both birds, covering in foil and masking tape again. I built up the rest of the birds bodies as before with foil and masking tape.

Now the birds were fully covered in tape I pushed them onto the 2 pin metal base and molded legs for the birds with foil and tape as before to secure them.

The clay I had made earlier was now ready to use, so I warmed it slightly by kneading. I took clumps and rolled it out into sheets about 5mm thick. Wet the underneath with a little water and smoothed onto the birds piece by piece. To blend the areas as one, I again used a little water my finger tips and a small pallet knife. I also made some feather molds from the clay and added to the tail area of the birds.

For the wings I used one of my favorite texture products…. paper decor, available in a variety of colours. Today I used pink because the blue Powertex is quite dark the colour of the paper decor won’t show through. I cut feather shapes out of it and worked blue Powertex liquid hardener into each piece before smoothing on both sides of the wings.

thumbnail_20190121_223100

Next I took Bronze (brown) stone art clay. Made with stone art and bronze brown Powertex art medium from a recent workshop. Rolled a long thin sausage shape and molded the beak shapes smoothing them into place. I covered the legs using stone art clay with my finger tips, a little water and small pallet knife.

thumbnail_20190121_101242

I created a small repetitive feather texture all over the birds body on the still wet clay. By pressing the silicone texture pad against areas I needed texture. I wanted to create webbed feet, using left over wire from the wings I shaped bird feet. And covered in masking tape before paining them black with black Powertex universal medium.

I decided to add wire crests to the birds to give extra interest. By pushing thin wire through the clay and curling them at the ends. I chose some green glass eyes and pushed them into the clay. I decided to be a little quirky with the colour of the legs, as I’m creating whimsical birds. So I painted the legs stripy using licorice twist and clotted cream acrylics.

thumbnail_20190121_175436

I left them to dry for a few hours so the clay would harden a little. So it was now time to bring them to life, by dry brushing with colours. For this I used Powertex powercolor and colortrix powder pigments mixed with easy coat varnish. I used orange and then faded yellow ochre in onto the beaks. I used ultramarine blue, then turquoise mixed with a little white. This makes the turquoise pop on the body and wings. Finishing by lightly dusting rich gold over the body and terra-green on the wings.

thumbnail_20190121_181126.jpg

Well the finished piece can be seen below…..Thanks for reading my first blog as part of the Powertex UK Design team. I hope you all enjoyed what I created this time. Do join me again next month when I’m back with another article.

thumbnail_20190121_210700

Don’t forget all the items used are hyperlinked. Click the highlighted text and it’ll take you straight to items you require, to save you time searching. Please don’t hesitate to comment or ask questions below.

In the mean time why not look through all the new and old blogs. Provided for you by the Powertex UK Design team and guests. You can also find me at The Crafty Little Corner. Send me a message if you would like to do this workshop with me. Or find me on my Facebook page sharing new ideas, hints, tips and a whole lot of Powertex inspiration.

Please spread the love and share this and other blogs.

Peace, love and Paradise 😉

Shell x

Step by step to techniques used to create a Powertex Box – Donna Mcghie

Hello and a very Happy New Year to everyone.

One of my resolutions for 2019 is to try and catch up with the modern age by getting to grips with videos in my blogs.   As you can also see, my daughter has been very helpful in getting them onto my computer for me, hence the titles of the videos.

What you will need to create your button tin:

Step by Step Instructions and Techniques:

1) As the box I was using was plastic I covered the base section with masking tape and then painted over this with Powertex Hardener so that the material would have something to adhere to.

2) I painted the lid with white gesso

IMG_20181228_171807-01
I painted the lid with white gesso so that my art deco image would show up

3) Once the bottom section was dry enough,  I turned it upside down and proceeded to soak strips of material in the Powertex Fabric Hardener and after squeezing out thoroughly placed them over the base.  At this point I was keeping the material nice and smooth as I laid it on as I wanted a flat bottom for my tin to rest on.

4) I dried this with a hair dryer and once dry enough, turned it over and started to work on my sides.  I wanted more texture on the sides, so scrunched up my fabric and added buttons as well.

IMG_20181229_154032-01
This is  a photo of the side once it has been dry brushed

If you want to you can also do this on the inside of your box.

5) Whilst this was drying off, I started to work on my lid.  I gently tore around the image I wanted to use from the Powertex Art Nouveau Rice Papers.  Then, using a good quality brush I brushed a little of the varnish onto the dried gesso, before carefully placing my image where I wanted it to go.  I then secured this in place by brushing over with a couple of more layers of varnish.  (NB: It is worth using a good quality brush for this as you want the image to be nice and smooth, the Powertex Brushes are perfectly designed for the job).

5) Once my image was in place, I carefully built up a pattern around it.  I wanted the most texture on my lid, so have done a short video to demonstrate how I did this.

6) Once the lid was covered, I added pieces of jewellery from my junk stash.  I also liked the idea of adding a frame, so used a small mdf one, and then, in memory of my nan and her tin, added some more buttons as well.

IMG_20181228_170255-01
I couldn’t resist adding a choker to my lady

7)  I left my box to dry off completely overnight

8) The next day it was time for my favourite part, dry brushing.  I wanted to give the impression of a bronze tin, whilst also subtly incorporating some of the colours on the Art Nouveau image, so I opted to use pigments in Bronze Gold, interference Blue and Interference Red.  Dry brushing is simple once you get used to the technique which is this:

  • Dip your flat brush into a small amount of Powertex Easy Varnish
  • Then dip the same brush into a small amount of whichever Powertex Pigment you have chosen
  • Now wipe the brush off on a sheet of paper towel.  This may counter productive, but it really is worth doing as you will get the best results when the brush is quite dry and will only pick out highlights, rather than smothering your design with thick colour.
  • Now you are ready to very gently, sweep your brush over your design.  Being sure to keep it flat.  You will be amazed at how quickly your design starts to come to life.

My best tip for dry brushing would be to start off gently and gradually build up to the depth of colour you want.

9) I did this over the whole of my tin.

10) And voila!! A rather bog standard plastic chocolate box that was destined to be added to landfill is now a  beautiful button box, in memory of a lovely lady.

IMG_20190102_112733-01
My finished box

I really enjoyed making this, and obviously similar boxes can be transformed in so many different ways – to reflect the personality of whoever you are making it for, or in memory of.

I hope you enjoyed this blog (please excuse the amateur video techniques, I will get better, I promise).  If you create your own version of one of these I would love to see it, and you can post photos on the Powertex Addicts Facebook Page

If you would like to see more about what I do, and why I do it my website page is www.artandmurals.co.uk

January – Product of the month – Stone Art Powder

Turquoise Powertex Stone Art Clay unicorn

Stone Art Powder – Find on the Powertex UK website.

3.jpg

Use Stone Art to make self-hardening clay, coarse and fine structures and stone effects.

Be inspired by more makes over on the Powertex UK Pinterest board.

Our Design Team and guests have shared some of their favourite makes with Stone Art Powder:

sam1.jpg

Sam Butler created these stunning Stone Art clay garden ornaments.sam2.jpg

This cute little chap is a wonderful hare created from Stone Art clay by Annette Smyth. 3.jpg

A wonderful bowl inspired by nature from Shell North.

4.jpg

Stone Art effect used on the side of this vase and on the clay flowers makes this piece a one of a kind treasure by Jill Cullum.5.jpg

Stone Art is just made for texture! Look at this amazing inter galactic work of art by Fi Potter.

3.jpeg

Stone Art can be used to sculpt adorable animals full of character as you can see with these fabulous owls by Donna Mcghie.

1.jpeg

Why not use Stone Art on your magical and practical ideas as Abigail Lagden has done with her works of art below.

0.jpg

2.jpg

Stone art works well as a clay and gives a stone effect will go on mdf bases and will cover Easy Structure and patterned wall paper for extra textural effects as seen on this hare was created by Anna Emelia Howlett.

14

Tracey Evans created this beautiful unicorn to teach as a project for the Powertex Garden Party and her portfolio workshops. Stamping into Stone art clay is another effective technique to create lots of detail in your work.

Portfolio Unicorn copy (1).png

Kore Sage brings us a piece of practical art with this stunning brush pot holder. With Powertex the possibilities really are endless.

StoneArtVase

We hope you have been inspired to get the Stone Art out and have a go! Do share your makes with us over in the Powertex Studio. See you next month with more Inspiration!

Christmas Powertex Creativeness – Jinny Holt

Well hello and seasons greetings to you all.

I do love Christmas and my Christmas mojo usually goes into overdrive at this time of year! So for my December blog, it would be rude NOT to do a Christmas tutorial and for this, I decided to do a Powertex Christmas tree. It is done with using a very few basic pieces of material and of course a bottle of Powertex. In this case, I used BRONZE POWERTEX

For this project, I used some cardboard, from which Powertex materials were delivered in,  Powertex, and an old pillowcase and some scraps of lace and sack cloth.

47579546_1170990973058346_7220253264854384640_n

I cut and shaped my cardboard into a cone shape and added masking tape to help secure it to its shape. I dipped my cut strips of pillowcase into my powertex and started wrapping the strips around the tree, the more strips you use the more texture you can create. I found some bits of lace and sackcloth and soaked these in Powertex and added them to my tree shape. I am a bit of a glue gun fanatic and decided to drizzle some hot glue down my tree shape.

Next for some colour, as I was doing this tree for a friend, she wanted a green tree, I used a mixture of colours and mediums, I started with some green acrylic and then added some Powertex pigment colours.48164589_2489309981083548_8377024022231121920_n

I have used some of the Art Lofts pearly pigment powders GOLDEN OLIVE and  to highlight and dry brush and of course, I used lots of gold LIMONCELLO GOLD!! I get kind of sidetracked when I add the colours and the pigments and it never ceases to amaze me, how your piece comes alive at this stage!

I left my tree overnight to dry off and then added some Christmas bits and pieces on it to complete the look of my tree.

So next time you think about throwing away that cardboard box, think again, what could it be? A bottle of powertex, a few bits and bobs and a pinch of imagination.

For all other ideas, tips and tricks with what you can do with Powertex try…

THE POWERTEX STUDIO

POWERTEX UK 

You can also find me on Facebook at Mums Shed

Thank you for reading this blog and I hope whatever you are doing over the Christmas season be safe and be happy and keep creating.

Until next month,

~Jinny~

Top Ten Tips for a Powertex Christmas – Annette Smyth

Hello Everyone

I don’t know about you but I just love this time of year.  I have Christmas movies and music playing in the background from the beginning of November!!

So in the spirit of the season,  I wanted to share some ideas with you on how to get a wintery festive feel into your projects.  So here are my top ten tips for Christmas crafting along with some festive musical titles (how many can you recognise?)………..

1. LET IT SNOW, LET IT SNOW, LET IT SNOW………

bKbHH%GzQUKlznYCVKHl+A

In my opinion you can never have enough snow!

Mix small 3D Balls and 3D Sand into White Powertex to get a textured snow effect. Experiment with different amounts of each until you get the consistency you need for your project.

Dry brushing with Powerpearl pigment makes the snow glisten.

2.  OH CHRISTMAS TREE, OH CHRISTMAS TREE ………

fullsizeoutput_15aa.jpegIcelandic/Reindeer moss coated in Transparent Powertex makes a lovely textured Christmas tree.  Be sure you give it enough time to dry – I left mine overnight, be careful if you use a hairdryer to speed up the process as you can burn the moss.

Here I have used moss that has been dyed bright green. The Powertex makes the dye bleed very slightly, so be aware of that when placing onto your project.

As the Powertex dried and became stickier,  I used a skewer to push the tree into shape.

3. (Christmas) PRETTY LIGHTS ON THE TREE……..

fullsizeoutput_15cd

Coat the large 3D Balls in Powertex and then dry brush with the pigments of your choice to make beautiful Christmas lights. To get a real shine coat with Easycoat Glossy. 

These can then be placed onto your tree and for a stringed light effect use Powercotton coated in transparent Powertex to connect the lights together.

4. DECORATIONS OF RED ON A GREEN CHRISTMAS TREE……

fullsizeoutput_1603

Well actually the decorations can be any colour you like.

Use Stoneart clay and your favourite silicon moulds to create decorations for your tree. Attach to your project using Transparent Powertex .

Watch the video in the Penguin blog to see how to make Stoneart clay.

Dry brush with pigments to complement your chosen colour scheme

5. MERRY CHRISTMAS MR BUBLE……

fullsizeoutput_15bb

Ok so I cheated on this title as I couldn’t think of any song with baubles in it……but you can’t have Christmas without a bit of Mr Buble.

Take a ball of Stoneart clay, insert a loop of cotton then coat with Easy Varnish.

Dip into glitter for a sparkly look or coat with your snow mix to look like a snowball.

6. WITH AN EVERGREEN WREATH ON A RED FRONT DOOR……..

4O2GKWnNS9eUvwBX+SZRlA

You can make a great Christmas wreath by using a mdf cog.  Coat with a layer of Powertex Green.  Dip strips of Paperdec into the Powertex and lay around the cog in a circular shape.

Dry brush with Colortricx Terragreen pigment and sprinkle on a little snow to finish your wreath.

7. DECK THE HALLS WITH BOUGHS OF HOLLY…………

fullsizeoutput_15d8

Use your Stoneart clay with any cutters you have to create embellishments.  Here I’ve used a sugarcraft holly leaf cutter with green clay.  Remember to keep these cutters for non food use only.

The holly berries are 3d Balls dipped  in Powertex and drybrushed with red pigment then coated with Easycoat Glossy.

8. WITH THOSE HOLIDAY GREETINGS AND GAY HAPPY MEETINGS……

fullsizeoutput_15e9

You can add any greetings you like into your project by using the mdf letters .

I coated mine in the base colour then placed them onto my project.  Using white Powertex I then painted over the top to make them stand out.

9. THE PRETTIEST PICTURE YOU’VE EVER SEEN IS CHRISTMAS IN KILLARNEY……

aYfLwRnhS9Oa+Yyg5ii4pw

You can add a focal point into your project by using the Powertex rice papers.  

Select the image you want to use and draw around it (leaving a small margin) using a wet paintbrush.  Now gently pull away the excess paper keeping your hand on the image, this way if you tear by mistake it will be the waste that you rip into and not your picture.

Attach to your project using Easycoat Matt.

10. RAISE A CUP OF CHRISTMAS CHEER………..

close up of beer glass against black background
After all your hardwork treat yourself to a little of what you like
Merry Christmas and Happy Creative Adventures…..see you all in the New Year
Axx